*The current sensor is providing accurate voltage readouts but amperage is inaccurate. This does not affect performance just note that the green wire under the tape and adhesive on the top plate is the wire to attach the video transmitter. *The video out for the vtx is being pulled from the top of the top plate rather than the normal pads as the normal video out pads where damaged while trying to remove my old 1.3ghz system. *There are a few spots with adhesive left from rearranging components *Naza lite can be rolled back from the V2 firmware easily if needed Setup Installation git clone Clone the project cd djinazainterfacec- make Build the librarys share object file. *BRIGHT LED strips front and rear for orientation To control the Naza V2 we need a relative pulse length that reaches from 102-512 (depends on calibration). *FRsky receiver available if desired (will ship without it unless you tell me you want it) *x2 Lipo Batteries 4s 5000mah one has about 50 cycles and the other is fairly new at 7 (turnigy hardcase packs removed from case) *Sunnysky X2212 motors with 10x4.5 HQ Props ![]() *Naza GPS with 32dBi antenna mod and fold down stand (gets 14 satellites outside and up to 9 in my living room) *Alexmos 32bit gimbal controller with second IMU (possibly able to upgrade to third axis later) Spironet LHCP Cloverleaf antennas on both ends Immersion RC 5.8GHz 600mW video transmitter Headplay HD FPV Glasses (will require a 12v power source such as a lipo) May accept lower offers, particularly if you have any 5.8ghz video transmitters or micro fpv cameras. ![]() You can message me here or go to the Ebay listing here: I have an FRSky receiver you can have you have a Taranis. The copter comes complete and ready to fly minus the need to install your own radio and receiver and your own GoPro Hero 3/3+/4 Camera and a 3s lipo pack to power the video glasses if flying FPV. 2) press and hold down the F/S button on the X8R (skip for Mode1) 3) power-on the X8R by plugging in a single servo cable from the powered model, e.g. Please contact your dealer for all technical support questions.For sale is my Team Blacksheep Discovery Pro Quadcopter. After everything is setup execute these steps. Please calibrate GPS again in good condition. GPS not calibrated, or magnetic field interference. ![]() It also requires the lion’s share of software-based. Please contact dealer (Place of purchase). The combination of FrSky’s Taranis X9D, ImmersionRC’s EzUHF system and DJI’s Naza-M V2 enables remote control of the Discovery Pro. TBS Discovery Build w/ DJI Naza and GoPro Hero 2 for FPV - Migrating from DJI Flamewheel F450 76,280 views 329 Dislike Share Save Dennis Baldwin 32K subscribers This is a. Installed the FatShark Vx (Video Transmitter) and DJI Naza PMU (Power Management Unit), connected GPS antenna 7. Installed the DJI Naza V2 FC (Flight Controller) 6. Installed the Graupner Rx (Radio Receiver) 5. IMU initialization failure, may be caused by crash. Attached DJI arms to the bottom plate and installed the spacers that separate the plates 4. COMPASS-ERRĬompass data is abnormal, please restart your Controller, if you still get this error, please contact your dealer (Place of purchase). Please make sure you are on the RC page of the NAZA Assistant Software, select the right receiver type or check the receiver connection, after that power cycle your controller to take effect. Please check the connection among battery, MC and PMU. You’ve chose parameters tuning by X1/X2 channel with Tx Knob, but no signal detected on X1/X2 input channel, or Tx didn’t powered on. Your S/N is not available, Please contact your dealer. Re-calibrate your transmitter, power cycle your controller, and check all of the parameters. ![]() Configuration error, this may cause by firmware upgrade from the old version, or abnormal Tx calibration.
0 Comments
Leave a Reply. |